24

2023

-

04

Correct operation and troubleshooting methods for fully automatic electric wire stripping machine

Classification :

Company News

Industry News


一、剥线机介绍

  剥线机就是将电线等外包裹的塑料包皮与金属芯剥离的机器,由于线径大小及线的材料及组成不一样有不同的适宜机型:短细线型、大平方型,排线型,护套线,同轴线型等电脑剥线机。 

二、剥线机的分类

智能电脑剥线机、高速剥线机、自动剥线机、电动剥线机、气动剥线机、电缆剥线机、排线剥线机,护套线剥线机,同轴线剥线机。 

三、剥线机设备的基本配件

 1. 进线轮:输送线材及剥出线头。剥线机在剥短线时既剥线头又剥线尾(线长小于50mm),在剥线机剥中剥的时候除剥线头外,还具备剥开中间几处的功能。 

2. Outlet wheel: convey the wire and strip the end of the wire for the stripping machine. (The stripping machine has no effect when stripping short wires, and the "outlet wheel lifting knob" needs to be in the "U" position)

3. Feed wheel gap adjustment knob: adjust the gap of the wire stripper, increase the gap of the upper rotation, and decrease the gap of the downward rotation (adjust according to the thickness of the wire).

4. Wire stripping machine inlet wheel pressure adjustment knob: adjust the inlet wheel pressure of the stripping machine, rotate clockwise after pulling out, the inlet wheel pressure increases, rotate counterclockwise after pulling out, and the inlet wheel pressure decreases. (Determined according to the strength of the wire skin, that is, the difficulty of peeling, the pressure increases, and the pressure decreases)

5. Lift the knob of the wire entry wheel: lift the wire entry wheel when the wire stripping machine is threaded, and turn the knob clockwise to lift the wire entry wheel so that it can pass through the wire smoothly; When working, lower the inlet wheel and turn the knob counterclockwise to lower the inlet wheel and press the wire.

6. Outlet wheel gap adjustment knob: adjust the outlet wheel gap for the stripping machine, increase the gap of rotation up, and decrease the gap of rotation down (adjust according to the thickness of the wire).

7. Outlet wheel pressure adjustment knob: adjust the outlet wheel pressure for the stripping machine, rotate counterclockwise after pulling out, the pressure of the outlet wheel increases, rotate clockwise after pulling out, and the pressure of the inlet wheel decreases. (Determined according to the strength of the wire skin, that is, the difficulty of stripping the wire stripper, the pressure increases, and the pressure decreases)

8. Lift the knob of the outlet wheel: lift the outlet wheel when taking out the wire, and turn the knob counterclockwise to lift the outlet wheel so that the wire can be taken out smoothly; When working, lower the outlet wheel, and turn the knob clockwise to lower the outlet wheel. (When using the short stripping procedure, the outlet wheel should be lifted)

9. Tool holder assembly: responsible for the cutting of the wire in the stripping machine, stripping head and tail, in the shutdown state, the upper and lower blades need to be opened to the maximum, so that the wire passes through the tool smoothly.

Fourth, the correct method of wire stripping machine operation

Turn on the power, manually go online, make the wire pass through the cutting knife edge, and then set the program and set the corresponding parameters, and finally the reverse cursor moves to the wire diameter when the knife, adjustment, repeated adjustment to the cutting wolf satisfactory can be, and then run a few lines to see the effect, if satisfied (length accuracy, line end accuracy, line end accuracy, no damage to the wire core) can be produced, if the wire core is injured, adjust the wire diameter or retract the knife, if the line head and line end have deviation, then adjust the corresponding decimal point, if the line length is biased, use the "add 1" "minus 1" key to correct. (The actual wire length may be longer or shorter than the set line due to different processing objects, which is an error caused by the plasticity of the wire itself.)

5. Troubleshooting methods

Phenomenon Solve the power supply interruption of the bill
1. Check whether the power
plug connection is good.

2. Whether the measurement voltage is 220V.

3. The power supply is suddenly interrupted during the operation of the machine.

The roller stops rotating
1. Press the "run" button in the shutdown state to confirm whether the roller rotates

2. After turning off the power, turn it back on and press the "Exit" button to confirm whether the scroll wheel turns.

The blade is not running normally
1. Check whether the screws of the tool holder connection parts are loose.

2. Whether the sensor at the lower left end of the blade is normal, clean the sticky object, confirm whether the sensor and the magnet are in the appropriate position, adjust the position of the sensor or replace the sensor with a new sensor if necessary

Stop when the blade comes down slightly
1. Add oil to the contact part where the blade moves.

2. Check whether the cut material is too hard.

3. Whether the blade is worn or not, it needs to be flattened or replaced