24

2023

-

04

Several Methods of Debugging Automatic Stripping Machine

Classification :

Company News

Industry News


一、自动剥线机的六个调整方式

下边我们一起来看一下自动剥线机的六个调整方法:

 将进气管连接气动阀门4.5-5kg/㎝2。

 插头电源线刺入380V50Hz开关电源。

 踩按钮开关以使汽缸措施。

 2个微调螺母是实际操作重要:将螺母管理中心之没头螺钉松掉,螺母1操纵上夹块左右;螺母2操纵激光刀模的左右,以指向大小不一样之线缆,将螺母往 上  涨(反方向)即是紧,往下降(顺时针方向)即是松。

 调节OK即卡紧管理中心之没头螺钉,尾端主汽缸为吊线汽缸,行程安排调理螺母为调节汽缸行程安排用,向前则行程安排愈短(如半剥时),往后面则愈长,去皮调节OK已然固定不动螺母卡紧。自动式自动剥线机汽缸上2个调阀门前后左右各自为调节去皮。回家之速率,速率应适度能一切正常应用就可以。

 大型号之应用压根跟上面一样相互,指向线缆需一次切剥成形而勾勒;需重视以下几个方面:未垫高口上皮细胞切割刀与剥皮刀中间间隙为1.5毫米;调整密封垫时干万重视左右薄厚相互,防止激光刀模磕磕碰碰,毁坏;去皮较长时将切割刀取下,就可以阵式应用,去皮长短由档线块操纵。

二、剥线机剥线速度设置

机器待机时(没有裁线),按下“剥线速度”键;切刀速度参数开始闪烁,此时可以直接输入数字,如果输入有误,可按“清零”键清除已输入的数字后再重新输入;然后按“确定”键保存,并且下一项参数闪烁,直至将切刀速度、送线速度、剥线速度、暂停时间全部输入完成;参数设置中;按“←”键将闪烁参数前移一项;按“→”键将闪烁参数后移一项;随时可以按“取消”退出参数设置,回到待机状态;

Output setting: When the machine is on standby (no cutting line), press the "Output Setting" button; The total amount setting parameter starts to flash, at this time you can directly enter the number, if the input is wrong, you can press the "clear" key to clear the entered number and then re-enter; Then press the "OK" key to save, and the next parameter flashes until the total amount of settings and the number of settings are all entered; in parameter settings; Press the "←" key to move the flashing parameter forward one item; Press the "→" key to move the flashing parameter back one item; You can press "Cancel" at any time to exit the parameter setting and return to the standby state;

Twist wire settings:

When the machine is on standby (no wire cutting), press the "twist wire setting" button; The front twist mode flashes, press the "↑", "↓" keys to switch, and then press the "OK" key to save, and the next parameter flashes until the front twist mode and the rear twist mode are entered, and then enter the twist speed and strength according to the previous method; in parameter settings; Press the "←" key to move the flashing parameter forward one item; Press the "→" key to move the flashing parameter back one item; You can press "Cancel" at any time to exit the parameter setting and return to the standby state;

Program number settings:

Working mode switching:

Third, how to use the computer stripping machine

1. Turn on the power switch behind the stripping machine, start the stripping machine, and set the screen light to light up;

Press the upper and lower health in the keyboard to select the program column,

The program means that if you have a line that will be repeatedly cropped in the future, set up this program and save it; In the future, directly select the program you defined to use it directly, no need to set it again;

2. Press the upper and lower keys in the keyboard to select the speed column

The speed is usually set to 05, if you want to be faster or slower when the machine is cutting normally, you can adjust it by adjusting the speed parameter; It is recommended not to be too fast and error-prone;

3. Press the upper and lower health in the keyboard to select the line length column,

The line length refers to how long you want to crop, set the number to as many as mm, the unit is mm, don't be wrong;

After the setting, be sure to cut one, verify whether the length is correct through the ruler on the machine (as shown in the figure), after all, the machine still has errors, if you can, put a little margin;

The yield does not need to be set, but the yield is set to 0000 before starting; This function is equivalent to a counter, which can be very intuitive to see from above

Cut

how much is it;

4. Press the upper and lower health in the keyboard to select to the line end, peel the head, the end of the line, peel the tail,

Here are four items directly explained together:

The thread head refers to how many mm the front line skin of the finished line is peeled off after cutting, and you can set it according to your needs.